We've stumbled on this article pertaining to How to Install a Bathtub Yourself listed below on the internet and felt it made good sense to write about it with you in this article.
Setting up a bath tub isn't exactly brain surgery, but it does require strong plumbing, woodworking, as well as often, tiling skills. Replacing an old bath tub with a new one is likewise a reasonably challenging project. If the old bathtub is readily available, the project can relocate speedily; if you need to open up a wall to get rid of the old bathtub and also place the new bath tub, the job is much harder. In either situation, the task is within a residence handyman's skills, although you will certainly need a helper to move out the old bathtub and embeded in the brand-new one. Make sure you have actually qualified yourself for the job and are comfortable trying it. Instead of hiring a contractor to take over a halfway-completed task, it is far better to consider using one before you begin. Chances are you may require an expert plumber to make tube links.
This article will certainly aid you install a new tub in your bathroom if you have currently acquired a new tub and don't require to alter the plan of your previous water pipelines.
Your tools as well as material list need to consist of the following:
Removing Old Touches
If you require to replace old faucets with new ones as a part of your installation, after that the first thing you ought to do is detach the water supply. After doing so, activate the faucets to drain any kind of water remaining in the system. The process of removing the existing faucets can be fairly troublesome because of the limited accessibility that is usually the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the faucets. Have a fabric ready for the continuing to be water that will come from the pipelines. Once the supply pipes have been eliminated, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from transforming during this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleansed of any old securing compound.
Prior to proceeding to fit the brand-new taps, compare the pipeline links on the old faucets to the new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the new faucets to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, after that you will need a plastic port to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and the various other end gives a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will require decreasing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the placing opening in the bath/basin making sure that the washing machines remain in location between the tap and the sink. Safeguard the tap in place with the maker offered backnut. When the faucet is firmly in place, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical tap ports. The former kind should be connected to the tap finishes initially, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Mounting the Bathtub
Using both wooden boards under its feet, position the tub in the called for setting. The wood boards are practical in equally spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 little factors.
The next objective is to ensure that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as changing the feet on the tub till the spirit level reviews degree.
To set up taps, fit all-time low of the outermost versatile tap adapter to the appropriate supply pipe by making a compression join; then do the exact same for the other tap.
Switch on the supply of water and check all joints and brand-new pipework for leakages as well as tighten them if required. Fill the bath tub as well as also check the overflow electrical outlet as well as the regular outlet for leakages.
Lastly, fix the bathroom paneling as described in the manufacturer's instruction manual. Tiling and also securing around the bathtub ought to wait up until the bathtub has been used at the very least once as this will certainly resolve it into its final position.
Planning for the Setup
To start with, the supporting frame supplied with the bath ought to be fitted (if needed) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is important to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps unit to stop stress on the tub.
Fit the flexible faucet ports to the bottom of the two faucets using 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Ensure you use all of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath must currently prepare to be suited its last placement.
Tiling Around the Bath tub
In the location where the bathroom satisfies the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate enough to crack an inflexible seal, triggering the water to pass through the wall in between the bath and the tiling, resulting in complications with moisture and also feasible leaks to the ceiling below.
You can select from a range of coloured sealants to assimilate your components and fittings. They are marketed in tubes and also cartridges, and are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of drenched paper or soft rope. Remember to always fill the tub with water before securing, to enable the movement experienced when the bathtub remains in use. The sealer can fracture fairly very early if you do not think about this activity prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise conveniently readily available on the market. It is a good idea to fit the tiles utilizing waterproof or water resistant sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been made aware of that article about Installing A Bathtub through someone on our other web address. Liked our write-up? Please share it. Let another person check it out. Thank you for your time invested reading it.
Top plumbers, one call.